含齿形裂隙类岩石材料单轴压缩试验研究

为研究含齿形裂隙岩石在单轴压缩下的破坏特征及强度特性，制作了含不同裂隙倾角和起伏角的齿形裂隙类岩石材料试件，并采用岩石力学伺服试验机进行单轴压缩试验。试验结果表明：（1）试件主要产生拉伸、剪切和拉剪复合裂纹，且根据裂纹的扩展路径可划分为A型（拉伸破坏）、B型（剪切破坏）、C型（复合破坏）3种破坏模式，裂隙倾角对试件最终破坏模式影响显著；（2）当裂隙倾角较小时，试件应力—应变曲线为多峰曲线，随着裂隙倾角的增大，曲线呈单峰形式，表现为延性减弱，脆性增强，而裂隙倾角相同但起伏角不同的试件应力—应变曲线大致相同；（3）当裂隙起伏角相同时，试件当量峰值强度随裂隙倾角的增大呈先减小后增大的规律，且裂隙起伏角对试件当量峰值强度的影响小于裂隙倾角。     

Simulation studies on a rotating ring disk electrode: Effects of ionic migration with kinetic complication-disk results

In continuation to my previous work (Guha S. AIChE J. 2013;59(4):1390-1399), in this work, effects of ionic migration are evaluated for disk region of a rotating ring disk electrode system by numerically solving complex differential equations, developed for mass transfer along with kinetic complication in presence of ionic migration under limiting current condition. The system for simulation is 0.01 M Fe₂(SO₄)₃ solution with H₂SO₄ as supporting electrolyte. Simulation cases are presence and absence of ionic migration with kinetic complication (oxidation of Fe²⁺ to Fe³⁺ under O₂ pressure). Results show that concentration boundary layer thickness of reactant Fe³⁺ reduces appreciably and steady-state disk current reduces substantially in presence of migration. Simulated steady-state disk current in absence of migration case agrees well with published data. Results indicate higher Fe²⁺ concentration in presence of migration and thereby higher rate of oxidation of Fe²⁺ to Fe³⁺ at all rate constant values.     

木片筛余物高得率半化学法清洁制浆技术研究

以太阳纸业备料车间木片筛选碎料（筛余物）为原料，对其烧碱法半化学制浆的实验室工艺和生产试验进行了研究。结果表明，筛余物采用半化学法制浆可获得较高得率和环压强度的纸浆，且用碱量对纸浆性能有显著影响。相对8%NaOH （相对于绝干原料）化学预处理，采用14%NaOH化学预处理结合两段浆浓22%的高浓磨浆工艺，所制半化学浆抄造浆张的裂断长和环压指数分别达2.89 km和9.76 N·m/g，是前者的1.9倍和1.2倍，而且优于现用国内OCC废纸浆抄造浆张；生产试验得到的浆张性能指标与实验室相吻合，其中紧度和环压强度分别达到GB/T 13023—2008瓦楞芯（原）纸AA级和A级优等品要求。     

Toughness enhancement and equivalent initial fracture toughness of cementitious composite reinforced with aligned steel fibres

Based on theoretical analysis and numerical simulation, the impact of steel fibres on the stress intensity factor (SIF) at the crack tip for cementitious composite was studied. The enhanced toughness of steel fibre reinforced cementitious composite (SFRC) in resisting cracks was explained by the decrement of SIF caused by steel fibre inclusions at the crack tip of the composite. The equivalent initial fracture toughness was used to characterize the crack initiation of SFRC. A simplified method for determining the of SFRC was proposed based on a linear regression method. Fracture tests were conducted on three‐point bending notched beams with different steel fibre volume fractions and specimen sizes to study the crack initiation behaviour of aligned steel fibre reinforced cementitious composite (ASFRC). of ASFRC was calculated, and the size effect of was analysed. The results showed that slightly increased with the steel fibre volume fraction and gradually became stable. For the tested specimens, whose heights varied between 40 and 100 mm, the specimen size had little impact on the .     

电磁精细探测法在隐伏型导水地质裂缝勘探中的应用

针对传统隐伏型导水地质裂缝勘探方法存在勘测精度较差的问题,提出电磁精细探测法探析隐伏型导水地质裂缝。依照屏蔽系数、实测场强和理论场强数据绘制综合曲线图,通过该图获取隐伏型导水地质裂缝所处位置几何阴影范围,采用层析成像法得到网格化的工作面,获取隐伏型导水地质图像。通过图像直接观测隐伏型导水地质工作面裂缝所处位置,在此基础上,观测四个电磁场分量,采用正交电磁场分量计算介质视电阻率,依据计算视电阻率数值和视电阻率分布状态研究裂缝发育情况和裂缝富水程度。结果表明:采用该方法能较为精准地获取隐伏型导水地质裂缝位置。通过裂缝位置进一步检测出隐伏型导水地质裂缝最大发育高度为63.5 m。当视电阻数值不断增加时,隐伏型导水地质裂缝和裂缝富水性逐渐减小,与实际情况较为相符,说明该种方法探析效果较好。     

Annular‐ring slot antenna designs with circular polarization radiation

The design of a microstrip‐fed annular‐ring slot antenna (ARSA) with circular polarization (CP) radiation is initially studied. To obtain CP radiation with broad 3‐dB axial ratio (AR) bandwidth that can cover the WiMAX 2.3 GHz (2305–2320 MHz, 2345–2360 MHz) and WLAN 2.4 GHz (2400–2480 MHz) bands, a novel technique of extending an inverted L‐shaped slot from the bottom section of the annular‐ring is proposed. To suppress the harmonic modes induced by the CP ARSA, the technique of integrating a defected ground structure into the annular‐ring slot is further introduced. From the measured results, 10‐dB impedance bandwidth and 3‐dB AR bandwidth of 44.86 and 9.68% were achieved by the proposed harmonic suppressed CP ARSA. Furthermore, average gain and radiation efficiency of ～4.7 dBic and 71%, respectively, were also exhibited across the bands of interest. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:337–345, 2015.     

转速对2524铝合金搅拌摩擦点焊组织与性能的影响

对2524铝合金薄板进行搭接搅拌摩擦点焊试验, 研究了搅拌头转速对其组织与性能的影响。结果表明, 随转速增加, 焊点外侧飞边越加严重, 组织畸变程度增加, 焊核区宽度增大, 有效连接宽度先增大后减小。母材区硬度最大, 热影响区硬度最低;在焊核区内, 显微硬度随转速增加而增大, 当转速为1 100 r/min时达到最大133.9HV, 而热影响区在300 r/min时硬度最大。在单向拉伸试验中, 接头剪切强度随转速增加先增大后减小, 在700 r/min时达到最大值3 510 N;接头呈现出两种断裂模式: 即低转速下平行于两板面断裂和高转速下沿倾斜方向断裂;断口呈现明显的剪切韧窝形态, 韧窝小而浅, 焊接接头为韧性断裂。